MEASUREMENT OF RESISTANCE RATIOS WITH DIGITAL VOLTMETER AND DAQ CARD – A
COMPARISON
การเปรียบเทียบ การวัดความต้านทานสัดส่วนของ เครื่องวัดแรงดันไฟฟ้าดิจิตอล กับ DAQ card
Abstract
This paper describes the comparison of the precise
digital voltmeters and DAQ cards in measurement of
resistance ratios. Recently, 24 bit DAQ cards have
emerged as possible measuring instruments that can
be used to develop precise measurement methods.
They are not as expensive as digital voltmeters, and
could replace digital voltmeters in many applications.
บทคัดย่อ
บทความนี้ อธิบายถึง เรื่องของการเปรียบเทียบที่แม่นยำ ระหว่าง เครื่องวัดแรงดันไฟฟ้าดิจิตอล กับ DAQ Card ใน การวัดสัดส่วนความต้านทาน เมื่อไม่นานมานี้ DAQ card แบบ 24 บิด ได้กลายเป็นเครื่องมือวัดที่สามารถถูกนำไปใช้ในการพัฒนาวิธีการวัดที่แม่นยำ พวกมันไม่ได้แพงเท่ากับเครื่องวัดแรงดันไฟฟ้าดิจิตอล(digital voltmeters) และอาจจะมาแทนเครื่องวัดแรงดันไฟฟ้าดิจิตอลในหลายๆ การใช้งาน
ไม่ทราบว่าแปลถูกหรือเปล่าครับ ??
แล้วรบกวนช่วยแปลตรงนี้ให้หน่อยครับ พอดีไม่เก่งคำนวนเลย ไม่รู้จะเอาคำไหนมาใช้ครับ ขอบคุณมากครับ
Mesaurement of resistance standards
To describe resistance comparison method
analytically, the next designations should be
considered. R1 represents known reference resistance,
and R2 represents unknown resistance, both are
realized with four terminals. Lead resistance,
including internal resistance of voltage source and
current relay's contact, is designated with Rp. Thicker
short lead is connected between current terminals of
compared resistors, marked as Rd. Digital voltmeters
DV1 and DV2 between H (high) and L (low)
terminals exhibit input resistances RV1 and RV2, as
shown in Fig. 1. Each of the voltmeters is measuring
DC voltage across one of the compared resistors, so
the relative errors can be assigned in accordance to
the general relation:
Umeasured = Utrue (1 + p) (1)
Therefore we can assign that:
U1a is the voltage measured by voltmeter DV1
across the resistor R1
U2a is the voltage measured by voltmeter DV2
across the resistor R2
U1b is the voltage measured by voltmeter DV1
across the resistor R2 (after voltmeter's positions
interchange)
U2b is the voltage measured by voltmeter DV2
across the resistor R1 (after voltmeter's positions
interchange).
ช่วยตรวจดูให้หน่อย อันนี้แปลถูกหรือเปล่าครับ??
COMPARISON
การเปรียบเทียบ การวัดความต้านทานสัดส่วนของ เครื่องวัดแรงดันไฟฟ้าดิจิตอล กับ DAQ card
Abstract
This paper describes the comparison of the precise
digital voltmeters and DAQ cards in measurement of
resistance ratios. Recently, 24 bit DAQ cards have
emerged as possible measuring instruments that can
be used to develop precise measurement methods.
They are not as expensive as digital voltmeters, and
could replace digital voltmeters in many applications.
บทคัดย่อ
บทความนี้ อธิบายถึง เรื่องของการเปรียบเทียบที่แม่นยำ ระหว่าง เครื่องวัดแรงดันไฟฟ้าดิจิตอล กับ DAQ Card ใน การวัดสัดส่วนความต้านทาน เมื่อไม่นานมานี้ DAQ card แบบ 24 บิด ได้กลายเป็นเครื่องมือวัดที่สามารถถูกนำไปใช้ในการพัฒนาวิธีการวัดที่แม่นยำ พวกมันไม่ได้แพงเท่ากับเครื่องวัดแรงดันไฟฟ้าดิจิตอล(digital voltmeters) และอาจจะมาแทนเครื่องวัดแรงดันไฟฟ้าดิจิตอลในหลายๆ การใช้งาน
ไม่ทราบว่าแปลถูกหรือเปล่าครับ ??
แล้วรบกวนช่วยแปลตรงนี้ให้หน่อยครับ พอดีไม่เก่งคำนวนเลย ไม่รู้จะเอาคำไหนมาใช้ครับ ขอบคุณมากครับ
Mesaurement of resistance standards
To describe resistance comparison method
analytically, the next designations should be
considered. R1 represents known reference resistance,
and R2 represents unknown resistance, both are
realized with four terminals. Lead resistance,
including internal resistance of voltage source and
current relay's contact, is designated with Rp. Thicker
short lead is connected between current terminals of
compared resistors, marked as Rd. Digital voltmeters
DV1 and DV2 between H (high) and L (low)
terminals exhibit input resistances RV1 and RV2, as
shown in Fig. 1. Each of the voltmeters is measuring
DC voltage across one of the compared resistors, so
the relative errors can be assigned in accordance to
the general relation:
Umeasured = Utrue (1 + p) (1)
Therefore we can assign that:
U1a is the voltage measured by voltmeter DV1
across the resistor R1
U2a is the voltage measured by voltmeter DV2
across the resistor R2
U1b is the voltage measured by voltmeter DV1
across the resistor R2 (after voltmeter's positions
interchange)
U2b is the voltage measured by voltmeter DV2
across the resistor R1 (after voltmeter's positions
interchange).